Showing at the Festival of Ideas Expo

Taste, measured.

eTongue is a benchtop electronic tongue for juice quality. One pour, four sensors: acidity, oxidation, conductivity and dissolved solids, read together on the device's own screen.

Universiti Malaysia PerlisEnfotec Sdn Bhd(MAKINA)

CAD render of the eTongue: a grey base with a display and red button, topped by a clear jar holding four probes in orange adapters.
pHacidity
ORPoxidation · mV
ECconductivity · µS/cm
TDSdissolved solids · ppm

Why eTongue

Taste is hard to measure

Juice makers check flavour by tasting and by lab testing. Both work, and both have limits.

Today

Taste panels

Trained tasters get tired, and people disagree. Results are hard to compare from one day to the next.

Today

Lab tests

Each property needs its own instrument and trained staff, so a full check takes several separate steps.

With eTongue

One sample, four readings

Four chemical sensors share one jar and read together, the same way every time. A batch that drifts from its usual profile stands out.

The sensors

Four probes, one jar

Each probe colour matches the probe in the renders.

pH0–14

Acidity

The main driver of sourness. Most fruit juices sit between pH 3 and 4.

DFRobot SEN0169-V2

ORPmV

Oxidation–reduction potential

Tracks oxidation, which changes colour and flavour as juice ages after opening.

DFRobot SEN0464

ECµS/cm

Electrical conductivity

Rises with dissolved minerals and salts, such as the potassium in fruit.

DFRobot SEN0451 · K = 1

TDSppm

Total dissolved solids

Estimated from conductivity. A rough guide to dilution. Sugar does not conduct, so this is not a Brix reading.

DFRobot SEN0244

Why four? One reading says little about taste on its own. Read together, the four numbers place a juice on a map, and juices that taste alike land close to each other. That is how an electronic tongue works.

Where juices sit on the pH scale (typical values)

2.3Lemon 3.5Orange 7.0Water

How it works

Pour, cap, press, read

  1. Pour

    Fill the jar with at least 510 mL of juice. The liquid has to reach 78 mm to cover the EC probe's sensing slot.

  2. Cap

    Fit the cap. Each probe sits in its own 3D-printed adapter, so all four tips stop 20 mm above the jar floor.

  3. Press

    Press the button on the front to start a reading.

  4. Read

    pH, ORP, EC and TDS appear on the 3.5″ display.

Cutaway render showing the display and controller at the front, eight signal and isolator boards on the base, and cable connectors at the rear.
Cutaway
Rear view render showing BNC sockets and cable glands on the back wall of the base.
Rear connectors
Front view render of the eTongue with its display and start button.
Front

Inside the device

Built for a wet bench

Size
130 mm wide, 329 mm tall with the jar fitted, 242 mm deep.
Brain
Single-board computer (Raspberry Pi class) behind a 3.5″ display.
Signal
Four signal boards, each with its own isolator. Without isolation, pH and ORP probes in the same liquid interfere with each other.
Probes
BNC sockets and cable glands on the rear, so the probes unplug for calibration and storage.
Jar seat
Raised collar holds the jar. A spill rim on the front and sides drains drips off the back, away from the display.
Cooling
Vent slots angled downward let heat out and keep drips out.
Made with
SolidWorks and CadQuery models, 3D-printed housing, cap and probe adapters.

The images are CAD renders of the current design. EC and TDS have no temperature compensation yet, so samples are measured near 25 °C.

Where it fits

Made for the people who make juice

Production checks

Compare each batch against a known good one before it is bottled.

Recipe development

See how a change in fruit, blend or dilution shifts the chemical profile.

Teaching labs

Show students how taste connects to acidity, oxidation and dissolved minerals.

Designed and built at Universiti Malaysia Perlis UniMAP
Developed for Enfotec Sdn Bhd MAKINA · Centre of Information & Technology

Come and see it

Visit us at the expo

See the eTongue in person at the Festival of Ideas Expo and talk to the team.

  • BoothAdd booth number
  • TeamAdd team member names
  • SupervisorAdd supervisor name
  • FacultyAdd faculty / programme